1. Peachtree Woodworking Supply#ad
2 Pack of 4 Way Pressure Clamps For Clamping Panels, Using Pressure From All Four Directions. Ideal For Woodworkers and Cabinet and Furniture Makers 2 four way pressure clamps#adPeachtree Woodworking Supply #ad - Wood is required for setting up the clamp. More than one clamp is generally recommended for any project over 12” in length. Build any length clamp with the durable plastic bars with 4 notches for maximum adjustability to handle a variety of stock widths. Now you can confidently glue up wide boards, table tops, apply wood glue to your project, and more up to 6” thick.
Wood is NOT included. Clamping panels can certainly be a challenge. Let’s make racked panel glue ups a thing of the past! the uniquely designed 4 way pressure solves this age old issue by applying pressure to all four sides of your panel glue up.
This provides equal pressure on to your panel and prevents bowing, buckling, or racked panels. Together, this setup will allow you to create two 4 way pressure clamps. Clamp can be used for boards up to 6 inches in thickness by simply adjusting the clamp width capacity with the appropriate number of notches. The 4 way pressure clamp is equipped with side pressure pads to prevent damaging your stock.
|Brand||Peachtree Woodworking Supply #ad|
|Manufacturer||Peachtree Woodworking Supply Inc.. #ad|
2. Deadwood Crafted Tools#ad
DCT 4-Way Pressure Release Clamp – Wood Panel Corner Clamping System Woodworking Bracket Set – For Stock up to 6 Inches#adDeadwood Crafted Tools #ad - Large panel glue-ups: the dct 4-way pressure release clamp – wood panel corner clamping System Woodworking Bracket Set handles stock up to 6 inches 15. 2cm thick for simplifying the process of gluing table tops, countertops, furniture panels, cabinet doors, and more and saves you from using additional clamps to keep the glue-ups straight.
Adjusts to your project: build any length clamp with the durable plastic bars with 12 notches for maximum adjustability to handle a variety of stock widths; Clamp can be used for boards up to 6 inches in thickness by simply adjusting the clamp width capacity with the appropriate number of notches; Turn the handle to tighten the clamp and unwind the turn handle to release pressure; Clamp has pressure pads to prevent damage to the edge of your stock.
5-inch x 1. 75-inch 3. 2cm x 4. 4cm board equivalent to a 2x4 ripped in half with provided screws, set clamp and turn handle to tighten on large pieces, we recommend one clamp every 18 inches/45. 7cm for maximum clamping efficiency; Make sure the 2x4s you use are not twisted; Drill pilot holes for the outer-most screws when attaching the pressure pads. Contents: package includes 2 12. 75-inch long notch bars, 2 6.
|Brand||Deadwood Crafted Tools #ad|
|Manufacturer||Deadwood Crafted Tools #ad|
|Warranty||This product has a manufacturer warranty against defects in materials and workmanship for a period of ONE (1) YEAR from the date of original retail purchase. See our Seller Return Policy for more details.|
Panel Max Glue Press Four Way 43 Inch Long Clamping System For Small and Large Panels. Keep Valuable Floor and Workbench Space Open While Gluing Up 39 Inch Maximum Width Flat Panels#adFulton #ad - The panel max glue press includes 1 each 39” mounting rail and 3 each 43” vertical clamp assemblies. The panel max has linking arms or more accurately a top and bottom pressure assembly that adjust to any thickness of stock from 0” up to 5”. To do this, or you can clamp multiple, clamp a couple of smaller panels edge to edge and leave out the glue between the first panel outer edge and the next starting edge of the adjacent panel to be glued.
With the max thickness stock of 5” you can clamp panel widths up to 39”. The package also includes full instructions to get you started and on your way to gluing up panels and boards with much less effort and aggravation than ever before! This alone is reason enough to include this system in your workshop collection of “go to” tools.
Of course, that’s not all. We recommend using one vertical clamp 12” apart on center. Each mounting rail is approx. Tired of buckled panels, heavy pipe clamps or loss of valuable floor or workbench space? yeah, we were too! The Panel Max Glue Press System not only eliminates each of these issues, messy gluing tables, it is also user friendly and can be expanded to accommodate most any size panel you need to glue up! It does all this while producing well laminated boards or flat panels each and every time you use it.
|Manufacturer||Fulton Woodworking Tools and Accessories #ad|
4. Pony Jorgensen#ad
PONY 50 Pipe Clamp, Fixture for 3/4-Inch Black Pipe#adPony Jorgensen #ad - Clamping faces are approximately 1-3/4” square. Clamping capacity only limited by length of pipe used. The product is 3/4" Pony Bar Clamp. Pony tools inc. Clamping capacity only limited by length of pipe used.
Multiple-disc-clutch design which allows a secure hold at any point along the pipe. S. Mounts on any length 3/4” black pipe with both ends threaded pipe not furnished. Pony tools makes all pony clamp Fixtures with U.
|Brand||Pony Jorgensen #ad|
12 Volts, 3.5 Gallons Per Minute, 45 Psi, Shurflo 2088-554-144 Fresh Water Pump#adSHURFLO #ad - Motor: permanent magnet, p/N 11-173-01, Thermally Protected. Voltage: 12 VDC Nominal. Cam: 3. 5 degree. Check valve: 1-way Operation Prevents Reverse Flow. Positive displacement 3 Chamber Diaphragm Pump.
6. AC Infinity#ad
Odor Control, Grow Rooms, for Inline Duct Fan, Hydroponics, AC Infinity Air Carbon Filter 6" with Premium Australian Virgin Charcoal#adAC Infinity #ad - Enables maximum airflow passthrough for both intake and exhaust configurations. Features premium-grade Australian charcoal with higher absorption and longer life rating. Designed to eliminate odors and chemicals for grow tents and hydroponics room.
|Brand||AC Infinity #ad|
|Manufacturer||AC Infinity #ad|
7. J-B Weld#ad
2 oz., J-B Weld 8265S Original Cold-Weld Steel Reinforced Epoxy#adJ-B Weld #ad - When fully cured, chemical and acid. Will set in 4-6 hours, and cure in 16-24 hours. Can be drilled, tapped, machined, filed, sanded and painted. J-b weld original: the original cold weld two-part epoxy system that was designed as an alternative to torch welding.
Once cured, filled, sanded, molded and drilled. Surface applications: metal, Concrete, plastic & PVC, Wood, Ceramic & Tile and Fiberglass. Versatile & dependable: j-b weld original is steel reinforced, j-b weld original is waterproof and resistant to petroleum, has a tensile strength of 5020 PSI and can withstand temperatures up to 550 degrees Fahrenheit 287 degrees Celsius.
Tensile strength is 3, 960 PSI. J-b weld original’s set and cure color is dark grey. Perfect for diy household, marine, automotive, craft repair and much more. Cure and set time: after mixing the tubes at a 1:1 ratio, j-b weld original can be tapped, it takes 4-6 hours to set and 15-24 hours to cure. Stong and nontoxic after it has set and temperature resistant up to 500F. J-b weld original provides strong, lasting repairs to multiple surfaces and creates a bond stronger than steel.
|Brand||J-B Weld #ad|
|Warranty||Please Contact Seller for Product Warranty Information.|
WEN 10236F2 Quick-Adjust 36-Inch Steel Bar Clamps with 2.5-Inch Throat and Micro-Adjustment Handle, Two Pack#adWEN #ad - Quick-adjust design: slide the clamp closed without pressing a single button. Micro-adjustment knob creates additional grip and precision. Includes two powerful F-clamps for a clamping force of over 1200 pounds across your workpiece.
Keadic 110Pcs 11 SIZE 7mm to 17mm Spring Hose Clamp Vacuum Clamp Spring Band Type Clamps Action Fuel/Silicone Vacuum Hose Pipe Clamp Low Pressure Air Clip Clamps Fasteners Assortment Kit#adKeadic #ad - Multiple specifications: our spring clamps kit includes 11 different sizes for mutiple hose sizes: 10 x 7mm 8mm 9mm 10mm 11mm 12mm 13mm 14mm 15mm 16mm 17mm inner diameter. Warm tips: you can show me your questions about our products and I would like to reply you within 12 hours.
Classified packaging: complete 110-piece spring band type clamps are packed neatly in a transparent Box separated into several compartments easy for classified packageing.
Besides, they are also good for lawnmowers, snowmobiles and motorcycle, water pipes and air tubes, etc. Wide applications: these spring type clamps are good selection for every handy man and home mechanic, widely used for various pipes fastening and connection such as automotive fuel/silicone vacuum hoses, etc.
CLP5SETN, Crescent 5 Piece 5", 7" & 10" Curved Jaw & 6" & 9" Long Nose Locking Pliers with Wire Cutter#adCrescent #ad - Compound action for powerful non-slip locking grip. Nickel-plated finish resists rust and corrosion. Adjust the pliers by winding the bottom screw from the hex key receiving hole. Versatile curved jaw also features integral wire cutter.
|Manufacturer||Apex Tool Group #ad|
|Warranty||Standard Limited Lifetime|