Category: Uncategorized

Top 8 Stepper Motor Driver Arduino – Electrical Motor Controls

As an Amazon Associate I earn from qualifying purchases.

1. Qunqi

#ad

Qunqi L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper For Arduino

#ad
Qunqi #ad - To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.

Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. Large capacity filter capacitance, afterflow protection diode, more stable and reliable. High working power to 35v, large current can reach 3A MAX and continue current is 2A, power to 25w. Dual-channel h-bridge driver working mode creates higher working efficiency, L298N as main chip. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.
BrandQunqi #ad
ManufacturerQunqi #ad
Height0.75 Inches
Length1.14 Inches
Weight0.07 Pounds
Width0.98 Inches
Part NumberMK-050
ModelCECOMINOD012186

2. STEPPERONLINE

#ad

STEPPERONLINE CNC Stepper Motor Driver 1.0-4.2A 20-50VDC 1/128 Micro-step Resolutions for Nema 17 and 23 Stepper Motor

#ad
STEPPERONLINE #ad - 1. 0~4. 2a, 20~50vdc, 1/128 microstep Resolution. Suit for nema 17 and 23 Stepper Motor. Industrial-grade Stepper Driver.
BrandSTEPPERONLINE #ad
ManufacturerOMC CORPORATION LIMITED #ad
Weight0.46 Pounds
Part NumberDM542T
ModelDM542T

3. diymore

#ad

Diymore 5pcs V44 A3967 EasyDriver Shield 7V-30V Stepper Motor Driver for Arduino EK1204 Support 4/6/8 Wires Stepper

#ad
diymore #ad - A3967 microstepping driver. Adjustable current control from 150mA/phase to 750mA/phase. A portion of each sales goes back to them for product support and continued development. Ms1 and ms2 pins broken out to change microstepping resolution to full, half, quarter and eighth steps defaults to eighth. The higher the voltage, the higher the torque at high speeds. This product is a collaboration with Brian Schmalz. Power supply range from 7v to 30V. Compatible with 4, 6, and 8 wire stepper motors of any voltage.
Branddiymore #ad
Manufacturerdiymore #ad
Part Number0102455

4. Qunqi

#ad

Qunqi 2Packs L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper For Arduino

#ad
Qunqi #ad - To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.

Large capacity filter capacitance, afterflow protection diode, more stable and reliable. High working power to 35v, large current can reach 3A MAX and continue current is 2A, power to 25w. Dual-channel h-bridge driver working mode creates higher working efficiency, L298N as main chip. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability.
BrandQunqi #ad
ManufacturerQunqi #ad
Weight0.11 Pounds
Part NumberMK-050-2
ModelMK-050-2

5. HONBAY

#ad

Honbay L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control & Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 Duemilanove Nano Robo

#ad
HONBAY #ad - L298n has such characteristics as strong driving ability, low calorific value and strong anti-interference ability. This module can use built-in 78m05 for electric work via a driving power supply part.

But to avoid the damage of the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage. Using large capacity filter capacitor, this module can follow current to protect diodes, and improve the reliability. Dual-channel H-bridge driver working mode creates higher working efficiency. L298n as main driver chip makes strong driving ability/small heating/strong.
BrandHONBAY #ad
ManufacturerHonbay #ad
Part NumberL298N-1P

6. DROK

#ad

DROK L298 Dual H Bridge Motor Speed Controller DC 6.5V-27V 7A PWM Motor Regulator Board 12V 24V Electric Motor Control Module Industrial 160W with Optocoupler Isolation, DC Motor Driver

#ad
DROK #ad - Pwm speed control: enable signal terminal ENA input PWM can regulate speed, PWM frequency range 0-10KHZ. Drok dc motor driver input voltage range is dc 6.

5v-27v, can be input dc 12v or 24v, rated output current of each port is 7A, total output power is 160W. Under voltage protection: the motor driver module is with under voltage protection to prevent instantaneous large current from damaging the module. Forward and revsersely rotate: the in1, in2/in3, in4 port can control forward or reverse motor rotation. Strong drive: the motor controller board adopts dual H bridge, can drive two DC motors at the same time.
BrandDROK #ad
ManufacturerDROK #ad
Part Number200206_OZ
Model200206_OZ

7. STEPPERONLINE

#ad

STEPPERONLINE Nema 17 Stepper Motor Bipolar 2A 59Ncm84oz.in 48mm Body 4-lead W/ 1m Cable and Connector compatible with 3D Printer/CNC

#ad
STEPPERONLINE #ad - Nema 17 bipolar 1. 65"x1. 65"x1. 89" 4-wire. 3d printer motor with high torque. 59ncm83. 6oz. In holding torque. Rated current 2. 0a & resistance 1. 4ohms. Build with 39. 37" 1m cable and 01" pitch Connector.
BrandSTEPPERONLINE #ad
ManufacturerOSM Technology Co.,Ltd. #ad
Height1.89 Inches
Length1.65 inches
Weight0.82 Pounds
Width1.65 Inches
Part Number17HS19-2004S1
Model17HS19-2004S

8. KOOBOOK

#ad

KOOBOOK 2Pcs L9110S 2 Channels DC Stepper Motor Dual Motor Driver Module Controller Board for Arduino

#ad
KOOBOOK #ad - It can drive two dc motors or one 4-wire 2-phase stepper motor at the same time. Double l9110S chip motor drive. With a fixed mounting hole, diameter: 3mm. Pcb size: 2. 8cm * 2. 1cm ultra-small size, suitable for assembly. Currently the smart car voltage and current are all within this range. Module supply voltage: 2. 5-12v. Suitable motor range: the motor working voltage is between 2. 5v-12v and the maximum working current is 08a.
BrandKOOBOOK #ad
ManufacturerKOOBOOK #ad
Part NumberKB045

metal